Скрытый текст

ALTVyacheslaV · 10.04.2012, 22:37

Добрый день. Принесли телефон Nokia 2710 Rm-586 с неисправностью зависает после выставления даты-времени. Я его прошил, телефон включился и работал, но были шумы в спикере при разговоре. Замена спикера не помогла и я решил перекатать процессор. При перекатке вырвал несколько пятаков. На Nokia X2 RM-618 стоит такой же точно проц Broadcom. Поставил его, телефон включается, но после подтвержения включения CS. Стер его полностью Бестом (кнопка Erase flash в Бесте), залил последнее ПО для 2710 (9,69), телефон стал включаться, но перегружается каждые пять минут, IMEI 1234.. Заказал RPL, рассчитали быстро, спасибо uo5oq. Новый RPL был вида RM-618_XXXXXXXXXXXXXXX.rpl. При записи RPL через бест и циклон имей не восстанавливается, хоть процесс проходит до конца.
Лог записи беста

Скрытый текст

Phone disconected!

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok

Will Write RPL keys now...
Check RPL file...
NPC Data found! (CMT)
CCC Data found! (CMT)
HWC Data found! (CMT)
SimLock Data found!
SimLock key found!
SuperDongle Key found!
WMDRM key found!
-> Skip Flash keys Part, for Flash Part use Dead Mode or Fbus

Writing SimLock Key... Error!
Writing SimLock Data... Error!
Writing Super Dongle Key... Ok!

SDD Key status : SD Data is Ok
SimLock status : SimLock is Ok
Security status : Security Damaged!!!!!

WMDRM_PD key sent... Ok

Done!

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok

Reading Phone Info....
Connected phone - Nokia 2710c-2
Software ver : V 09.69 22-03-11 RM-586 (c) Nokia
IMEI : 12345610654321?
Ape Ver :
APE Var :
APE ADSP:
DSP Ver :
APE Test:
PPM : V 09.69 22-03-11 RM-586 (c) Nokia I
CNT : Content: i_ru_black V 09.69 22-03-11 RM-586 (c) Nokia
Product SN : 0
Product code :
Base Prd.code:
Module code :
Long Prod.SN : 0
Hardware info=======
HWID :
Retu :
Tahvo :
Batery: 3923 mV
Camera:
CMT BT: 3.11-SP2.19
APE BT:
APE HW:
LCDVer: SEIKO
RF ic :
Lock info ===========
IMEI : 12345610654321?
IMEI spNet : 1A 32 54 16 60 45 23 01
IMEI svNet : 13 32 54 16 60 45 23 71 F0

Unable to read Lock table...

IMEI DAMAGED!!! CRT308 save skipped...

SDD key status : Ok
SimLock status : Ok
Security status : Damaged!!!!!
PA_SL phone

User code : Crypted
MMC pwd : no any record found
UserDataExLevel : Full [PhoneBook, Calendar, PWD, SMS, Gallery]

Done!

Лог записи RPL циклоном:

Скрытый текст

Skipping RPL decryption...
Parsing decrypted RPL...
Processing FBUS Part...
[Nokia 2710 Navigation Edition USB Phonet]: Port opened OK!
Handling as Universalbox Backup
Writing Simlock...
Handling as SL3 Simlock Data
Handling as SIMLOCK2 Format
Reading Security Block...
Security block OK and saved to "RM-586_12345610654321_11.04.2012_10438.SecurityBlock.PM"
15 Digits NCK Found
Simlock ACCEPTED OK !
Writing Superdongle key...
Superdongle Key ACCEPTED OK !
Writing WMDRM PD Data...
WMDRM PD Data NOT ACCEPTED !
Processing FLASHBUS Part...
Booting CMT...
[Nokia 2710 Navigation Edition USB Phonet]: Port opened OK!
Switching to RAW Mode...
[Nokia USB Flashing Generic]: Port opened OK!
New ROM Detected
CMT_SYSTEM_ASIC_ID: 000000000000000022000509200C0000
CMT_EM_ASIC_ID: 00005361
CMT_PUBLIC_ID: 00000000001D4F51D862FF7DDA3043DCBD40A3C2
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 1B0D74C532CA1C6133940C740E8C786E
CMT_BOOT_ROM_CRC: DE56D582
CMT_SECURE_ROM_CRC: BDDE7A3A
CMT Ready!
Searching for BootCode: DualLine 32Bit
BCM21351_usb2nd.fg, Type: 2nd Boot Loader, Rev: 513.11.40.0, Algo: BB5
Using NEW BB5 FLASHING PROTOCOL
Transmission Mode Requested: Control USB, Accepted: Control USB
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC003000000321, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0030 (Samsung), Size: 128MBytes, VPP: Not Supported
BCM21351_XSR16_usbalg.fg, Type: Algorithm, Rev: 513.11.40.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Transmission Mode Requested: Bulk USB, Accepted: Bulk USB
Box TX2 Data Pin set to: Service Pin 3
Waiting for FUR Client become avaiable...
[Nokia USB Flashing Generic]: Port opened OK!
FUR Avaiable!
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Overriding VPP Setting, USB can't use VPP
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 84CDC75F79F52BBAE46EA3A70C9240861412C480
APE Subsystem Not Found
CMT NPC Erased
CMT NPC Written
CMT HWC Erased
CMT HWC Written
CMT CCC Erased
CMT CCC Written
Restarting MCU...
Write RPL Finished!
MCU Version V 09.69
MCU Date 22-03-11
Product RM-586 (Nokia 2710c-2)
Manufacturer (c) Nokia
IMEI 12345610654321?
IMEI Spare 1A32541660452301
IMEI SV 1332541660452371F0000000
PPM V 09.69, 22-03-11, RM-586, (c) Nokia , I
CNT Content: i_ru_black, V 09.69, 22-03-11, RM-586, (c) Nokia
PSN 0
PSD 0000000000000000
LPSN 0
RFIC 9
LCD SEIKO
BT 3.11-SP2.19
Failed to read info -> Failed to read SP info

После записи RPL телефон при включении спрашивает с симкой или без и потом CS. Из оборудования UFS, JAF, Cyclone, MX-Key, Best. Помогите пожалуйста

еще меня удивило, что после записи RPL и попытке прошить телефон через Best он бэкапит сертификаты в файл вида КупленныйIMEI.rpl, хотя при чтении INFO оба программатора показываю что IMEI вида 1234
лог прошивки Бестом после заливания RPL

Скрытый текст

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok

Phone disconected!

Connect phone on selected interface...

Core : v1.42 , FlashEngine : v1.25

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm586__09.69.mcusw
PPM : rm586__09.69.ppm_i
CNT : rm586__09.69.image_i_ru_black
Flashing phone now...
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
BootRom : 1st boot ok
ASIC ID: 000000000000000022000509200C0000
CPU ID : BroadCom 21351 , Features : Dead-Test, USBCRT, FullUSB
EM0 ID: 00005361
PUBLIC ID: 00000000001D4F51D862FF7DDA3043DCBD40A3C2
ASIC MODE ID: 00
ROOT KEY HASH: 1B0D74C532CA1C6133940C740E8C786E
ROM ID: DE56D582BDDE7A3A
Use BCM21351_usb2nd.fg , Rev : 2.1 Ver : 11.50.0
Processing RAWLOADER...
FLIC : 003000EC
Req : XSR 1.6
Use BCM21351_XSR16_usbalg.fg , Rev : 2.1 Ver : 11.50.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done!

TIME : Boot time : 00:00:05
Reopening the connection...
Waiting for response: 30
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : blank (Erased or HW failure)
ADL: phone is in flash mode

Backup enabled, will read all certificates...
Reading NPC certificate...
IMEI : 355367048941896
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Reading PARTNERC certificate...
Reading MDM_KEYS certificate...
Cert Read done!

NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...

RPL saved : c:\Program files\BEST\Backup\Cert\XXXXXXXXXXXX1896_CRT_2nd.rpl <---это имей купленного RPL

===Flashing [MCU]===
Erase : Processing rm586__09.69.mcusw
Partitioning....
Partitioning Ok...
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm586__09.69.mcusw
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [ADA]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [RAP3NAND]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [UPDAPP]
CMT: Writing Hash CERT [MCUSW]
CMT: Writing Hash CERT [GENIO_INIT]
Total writen 466 blocks
TIME : Write time : 00:00:32
MCU Write done
ADL: Request programm status
NAND status : 00000001 / 00000001 / 00000000

===Flashing [PPM]===
Erase : Processing rm586__09.69.ppm_i
Partitioning....
Partitioning Ok...
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm586__09.69.ppm_i
Total writen 91 blocks
TIME : Write time : 00:00:05
PPM Write done
ADL: Request programm status
NAND status : 00000001 / 00000001 / 00000000

===Flashing [CNT]===
Erase : Processing rm586__09.69.image_i_ru_black
Partitioning....
Partitioning Ok...
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:01
Write : Processing rm586__09.69.image_i_ru_black
Total writen 202 blocks
TIME : Write time : 00:00:12
CNT Write done
ADL: Request programm status
NAND status : 00000001 / 00000001 / 00000000

ADL: Close_Session
Content: 000300000000010000000100000000
ADL: Reboot

Flashing done!
Total flash time : 00:00:52
Reboot phone now...

Reading Phone Info....
Connected phone - Nokia 2710c-2
Software Info: V 09.69 22-03-11 RM-586 (c) Nokia
IMEI: 12345610654321?
PPM version : V 09.69 22-03-11 RM-586 (c) Nokia I
Product code:
Checking...
SimLock status : SimLock is Ok
Security status : Security Damaged!!!!!

Read Info Done!
Settings After Flash Defaults...
ProductTuneSet...OK!
SwUpgradeSet...OK!
Checking User Certificates...
Total - 34 certs
Data exist, skip certificate repair...
AfterFlash operations done ;D
Done!

10.04.2012, 22:37	#1
ALTVyacheslaV Junior Member Регистрация: 28.02.2012 Сообщений: 8 Вес репутации: 0	Ошибка записи RPL в Nokia 2710 после замены процессора Добрый день. Принесли телефон Nokia 2710 Rm-586 с неисправностью зависает после выставления даты-времени. Я его прошил, телефон включился и работал, но были шумы в спикере при разговоре. Замена спикера не помогла и я решил перекатать процессор. При перекатке вырвал несколько пятаков. На Nokia X2 RM-618 стоит такой же точно проц Broadcom. Поставил его, телефон включается, но после подтвержения включения CS. Стер его полностью Бестом (кнопка Erase flash в Бесте), залил последнее ПО для 2710 (9,69), телефон стал включаться, но перегружается каждые пять минут, IMEI 1234.. Заказал RPL, рассчитали быстро, спасибо uo5oq. Новый RPL был вида RM-618_XXXXXXXXXXXXXXX.rpl. При записи RPL через бест и циклон имей не восстанавливается, хоть процесс проходит до конца. Лог записи беста Скрытый текст Phone disconected! Connect phone on selected interface... Phone found! Series 40 Device detected! read info... - Ok Will Write RPL keys now... Check RPL file... NPC Data found! (CMT) CCC Data found! (CMT) HWC Data found! (CMT) SimLock Data found! SimLock key found! SuperDongle Key found! WMDRM key found! -> Skip Flash keys Part, for Flash Part use Dead Mode or Fbus Writing SimLock Key... Error! Writing SimLock Data... Error! Writing Super Dongle Key... Ok! SDD Key status : SD Data is Ok SimLock status : SimLock is Ok Security status : Security Damaged!!!!! WMDRM_PD key sent... Ok Done! Connect phone on selected interface... Phone found! Series 40 Device detected! read info... - Ok Reading Phone Info.... Connected phone - Nokia 2710c-2 Software ver : V 09.69 22-03-11 RM-586 (c) Nokia IMEI : 12345610654321? Ape Ver : APE Var : APE ADSP: DSP Ver : APE Test: PPM : V 09.69 22-03-11 RM-586 (c) Nokia I CNT : Content: i_ru_black V 09.69 22-03-11 RM-586 (c) Nokia Product SN : 0 Product code : Base Prd.code: Module code : Long Prod.SN : 0 Hardware info======= HWID : Retu : Tahvo : Batery: 3923 mV Camera: CMT BT: 3.11-SP2.19 APE BT: APE HW: LCDVer: SEIKO RF ic : Lock info =========== IMEI : 12345610654321? IMEI spNet : 1A 32 54 16 60 45 23 01 IMEI svNet : 13 32 54 16 60 45 23 71 F0 Unable to read Lock table... IMEI DAMAGED!!! CRT308 save skipped... SDD key status : Ok SimLock status : Ok Security status : Damaged!!!!! PA_SL phone User code : Crypted MMC pwd : no any record found UserDataExLevel : Full [PhoneBook, Calendar, PWD, SMS, Gallery] Done! Лог записи RPL циклоном: Скрытый текст Skipping RPL decryption... Parsing decrypted RPL... Processing FBUS Part... [Nokia 2710 Navigation Edition USB Phonet]: Port opened OK! Handling as Universalbox Backup Writing Simlock... Handling as SL3 Simlock Data Handling as SIMLOCK2 Format Reading Security Block... Security block OK and saved to "RM-586_12345610654321_11.04.2012_10438.SecurityBlock.PM" 15 Digits NCK Found Simlock ACCEPTED OK ! Writing Superdongle key... Superdongle Key ACCEPTED OK ! Writing WMDRM PD Data... WMDRM PD Data NOT ACCEPTED ! Processing FLASHBUS Part... Booting CMT... [Nokia 2710 Navigation Edition USB Phonet]: Port opened OK! Switching to RAW Mode... [Nokia USB Flashing Generic]: Port opened OK! New ROM Detected CMT_SYSTEM_ASIC_ID: 000000000000000022000509200C0000 CMT_EM_ASIC_ID: 00005361 CMT_PUBLIC_ID: 00000000001D4F51D862FF7DDA3043DCBD40A3C2 CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: 1B0D74C532CA1C6133940C740E8C786E CMT_BOOT_ROM_CRC: DE56D582 CMT_SECURE_ROM_CRC: BDDE7A3A CMT Ready! Searching for BootCode: DualLine 32Bit BCM21351_usb2nd.fg, Type: 2nd Boot Loader, Rev: 513.11.40.0, Algo: BB5 Using NEW BB5 FLASHING PROTOCOL Transmission Mode Requested: Control USB, Accepted: Control USB FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR FlashChip[0,CMT]: 0x00EC003000000321, Samsung, ONENAND Requested Algorithm: XSR 1.6 (CMT) Searching for BootCode: DualLine 32Bit FlashChip 0x00EC0030 (Samsung), Size: 128MBytes, VPP: Not Supported BCM21351_XSR16_usbalg.fg, Type: Algorithm, Rev: 513.11.40.0, Algo: XSR 1.6 Initializing TurboCache... TurboCache Loaded! Writing CMT PASUBTOC Certificate... Writing CMT ALG Certificate... CMT Algorithm Ready! Transmission Mode Requested: Bulk USB, Accepted: Bulk USB Box TX2 Data Pin set to: Service Pin 3 Waiting for FUR Client become avaiable... [Nokia USB Flashing Generic]: Port opened OK! FUR Avaiable! Adding FUR Client (CMT, State: Ready)... CMT FUR Ready! Overriding VPP Setting, USB can't use VPP Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: 84CDC75F79F52BBAE46EA3A70C9240861412C480 APE Subsystem Not Found CMT NPC Erased CMT NPC Written CMT HWC Erased CMT HWC Written CMT CCC Erased CMT CCC Written Restarting MCU... Write RPL Finished! MCU Version V 09.69 MCU Date 22-03-11 Product RM-586 (Nokia 2710c-2) Manufacturer (c) Nokia IMEI 12345610654321? IMEI Spare 1A32541660452301 IMEI SV 1332541660452371F0000000 PPM V 09.69, 22-03-11, RM-586, (c) Nokia , I CNT Content: i_ru_black, V 09.69, 22-03-11, RM-586, (c) Nokia PSN 0 PSD 0000000000000000 LPSN 0 RFIC 9 LCD SEIKO BT 3.11-SP2.19 Failed to read info -> Failed to read SP info После записи RPL телефон при включении спрашивает с симкой или без и потом CS. Из оборудования UFS, JAF, Cyclone, MX-Key, Best. Помогите пожалуйста еще меня удивило, что после записи RPL и попытке прошить телефон через Best он бэкапит сертификаты в файл вида КупленныйIMEI.rpl, хотя при чтении INFO оба программатора показываю что IMEI вида 1234 лог прошивки Бестом после заливания RPL Скрытый текст Connect phone on selected interface... Phone found! Series 40 Device detected! read info... - Ok Phone disconected! Connect phone on selected interface... Core : v1.42 , FlashEngine : v1.25 Selected FlashSettings : Manual Check FlashFiles, Please, wait... Files Set for Flashing : MCU : rm586__09.69.mcusw PPM : rm586__09.69.ppm_i CNT : rm586__09.69.image_i_ru_black Flashing phone now... Check files done... -> SWversion check skipped : Dead mode selected Dead Mode is Selected Waiting for USB device... --- Insert cable and charger or press phone's power button! --- Connection opened successfully Waiting for communication response... BootRom : 1st boot ok ASIC ID: 000000000000000022000509200C0000 CPU ID : BroadCom 21351 , Features : Dead-Test, USBCRT, FullUSB EM0 ID: 00005361 PUBLIC ID: 00000000001D4F51D862FF7DDA3043DCBD40A3C2 ASIC MODE ID: 00 ROOT KEY HASH: 1B0D74C532CA1C6133940C740E8C786E ROM ID: DE56D582BDDE7A3A Use BCM21351_usb2nd.fg , Rev : 2.1 Ver : 11.50.0 Processing RAWLOADER... FLIC : 003000EC Req : XSR 1.6 Use BCM21351_XSR16_usbalg.fg , Rev : 2.1 Ver : 11.50.0 Processing PASUBTOC ... Processing ALG ... Boot Done! TIME : Boot time : 00:00:05 Reopening the connection... Waiting for response: 30 ADL: Check mode Select ASIC [C900] PAPUBkeys : blank (Erased or HW failure) ADL: phone is in flash mode Backup enabled, will read all certificates... Reading NPC certificate... IMEI : 355367048941896 Reading CCC certificate... Reading HWC certificate... Reading R&D certificate... Reading VARIANT certificate... Reading PARTNERC certificate... Reading MDM_KEYS certificate... Cert Read done! NPC Certificate saved... CCC Certificate saved... HWC Certificate saved... RPL saved : c:\Program files\BEST\Backup\Cert\XXXXXXXXXXXX1896_CRT_2nd.rpl <---это имей купленного RPL ===Flashing [MCU]=== Erase : Processing rm586__09.69.mcusw Partitioning.... Partitioning Ok... Erasing.... Erasing Ok... TIME : Erase time : 00:00:00 Write : Processing rm586__09.69.mcusw CMT: Writing Hash CERT [KEYS] CMT: Writing Hash CERT [ADA] CMT: Writing Hash CERT [PRIMAPP] CMT: Writing Hash CERT [RAP3NAND] CMT: Writing Hash CERT [PASUBTOC] CMT: Writing Hash CERT [PAPUBKEYS] CMT: Writing Hash CERT [UPDAPP] CMT: Writing Hash CERT [MCUSW] CMT: Writing Hash CERT [GENIO_INIT] Total writen 466 blocks TIME : Write time : 00:00:32 MCU Write done ADL: Request programm status NAND status : 00000001 / 00000001 / 00000000 ===Flashing [PPM]=== Erase : Processing rm586__09.69.ppm_i Partitioning.... Partitioning Ok... Erasing.... Erasing Ok... TIME : Erase time : 00:00:00 Write : Processing rm586__09.69.ppm_i Total writen 91 blocks TIME : Write time : 00:00:05 PPM Write done ADL: Request programm status NAND status : 00000001 / 00000001 / 00000000 ===Flashing [CNT]=== Erase : Processing rm586__09.69.image_i_ru_black Partitioning.... Partitioning Ok... Erasing.... Erasing Ok... TIME : Erase time : 00:00:01 Write : Processing rm586__09.69.image_i_ru_black Total writen 202 blocks TIME : Write time : 00:00:12 CNT Write done ADL: Request programm status NAND status : 00000001 / 00000001 / 00000000 ADL: Close_Session Content: 000300000000010000000100000000 ADL: Reboot Flashing done! Total flash time : 00:00:52 Reboot phone now... Reading Phone Info.... Connected phone - Nokia 2710c-2 Software Info: V 09.69 22-03-11 RM-586 (c) Nokia IMEI: 12345610654321? PPM version : V 09.69 22-03-11 RM-586 (c) Nokia I Product code: Checking... SimLock status : SimLock is Ok Security status : Security Damaged!!!!! Read Info Done! Settings After Flash Defaults... ProductTuneSet...OK! SwUpgradeSet...OK! Checking User Certificates... Total - 34 certs Data exist, skip certificate repair... AfterFlash operations done ;D Done!