Подключил Best через UFS. К сожалению вот такой лог:
Core : v1.95 , BB5XG FlashEngine : v9.9
Selected FlashSettings : Manual
Files Set for Flashing :
MCU : rm443__10.12.mcusw
PPM : rm443__10.12.ppm_i
CNT : rm443__10.12.image_i_bg_ua_matt_black
Check FlashFiles, Please, wait...
-> SWversion check skipped : Dead mode selected
Setting FlashMode
FlashMode set Ok
1st boot Ok, C0
CMT part info :
CMT ASICID : 000000010000022600010006030C192101033000
CMT EM0 ID : 00000295
CMT EM1 ID : 00000B22
CMT PUB ID : 2390000683C48A56CF3FCDEB99FE50BFEA54C5E1
CMT MODE ID : 00
CMT R_HASH : 9DDBFCFE6E73CED7D8C6268C8EB85723
CMT ROM ID : 273F6D55DFAAF68F
CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg , Rev : 0.0 Ver : 10.42.0
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 89820089 , CMT , NOR
CMT Flash ID : 89820089 < INTEL => 0046L0Y1GG/NU48F512
FLCNT : 000000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo_v1331.fg , Rev : 0.0 Ver : 1.33.1
CMT Algo sent
PAPUBkeys blank (erased or HW failure)
Transmission mode : Dual (Ddr, TX2)
Boot Done!
Transmission mode : Dual (Ddr, TX2)
Erase : Processing rm443__10.12.mcusw
Found 8 areas to erase, erase group
Asic : CMT , Sub : NOR
CMT , NOR , Area : 0x00000000 - 0x0001FFFF
CMT , NOR , Area : 0x00040000 - 0x0005FFFF
CMT , NOR , Area : 0x00060000 - 0x0007FFFF
CMT , NOR , Area : 0x00080000 - 0x0015FFFF
CMT , NOR , Area : 0x00160000 - 0x0023FFFF
CMT , NOR , Area : 0x01740000 - 0x0191FFFF
CMT , NOR , Area : 0x00240000 - 0x0173FFFF
CMT , NOR , Area : 0x022E0000 - 0x0261FFFF
Using TimeOut : 7 min ( 430 sec )
Erasing, wait.....
CMT : Group erase Ok
TIME : Erase time : 00:00:06
PrReq : NOR , 00
Transmission mode : Dual (Ddr, TX2)
Write : Processing rm443__10.12.mcusw
Error, 03, DataMissMatch, Check Cable, FlashPack, Firmware
Error write block at : 1
ERR : C7012D0103CD000010000000
Error on Flashing Phone!
- > Error...
Connect phone on selected interface...
Connect phone on selected interface...
Клиент достал, надо дать ему ответ... Покупаю ли я ему новый 6303 или может можно еще что-то сделать?