[Андрей]

Значит поступим так.
Вопрос у меня еще, вот лог стирания и записи SW Cyclon-ом, Best не стерает

[Nokia USB Flashing Generic]: Port opened OK!
Old ROM Detected
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102031104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		26200217F7DC03442FDD9D537AC049A64CB54B81
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	916F75217F32081248B15C38DFC8E81B
CMT_BOOT_ROM_CRC:	E693EF0D
CMT_SECURE_ROM_CRC:	AC22615B
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Using NEW BB5 FLASHING PROTOCOL
Waiting for USB Boot ROM Answer...
ROM Ret: 0xFFFD125D
ROM CMT dwAddr: 0x10004FF0
ROM CMT dwLength: 0x00627837
Seems ROM Initialized OK!
Transmission Mode Requested: Control USB, Accepted: Control USB
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0020006800000031, ST, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x0020006800000031, ST, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00200068 (ST), Size: 1024MBytes, VPP: Not Supported
FlashChip 0x00200068 (ST), Size: 1024MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Transmission Mode Requested: Bulk USB, Accepted: Bulk USB
Box TX2 Data Pin set to: Service Pin 3
Waiting for FUR Client become avaiable...
[Nokia USB Flashing Generic]: Port opened OK!
FUR Avaiable!
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Overriding VPP Setting, USB can't use VPP
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: C436DE8B3DEA6D6C6CCE9CBE15F7C501BB822D02
APE Subsystem Not Found
Erasing flash chip...
Started group flash erase
EraseArea[0,CMT]: 0x00000000-0x3FFFFFFF, ONENAND
Waiting 640s for erasure finish...
Erase taken 13.562s
Restarting MCU...
BB5 Full Erase Finished!
Processing pre flash tasks...
Backing up RPL...
RPL Creation started...
Processing CMT Part...
[Nokia USB Flashing Generic]: Port opened OK!
Warning: Phone not detected, using Rap Public ID in FileName and reading Certificates Only
Booting CMT...
[Nokia USB Flashing Generic]: Port opened OK!
Old ROM Detected
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102031104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		26200217F7DC03442FDD9D537AC049A64CB54B81
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	916F75217F32081248B15C38DFC8E81B
CMT_BOOT_ROM_CRC:	E693EF0D
CMT_SECURE_ROM_CRC:	AC22615B
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Using NEW BB5 FLASHING PROTOCOL
Waiting for USB Boot ROM Answer...
ROM Ret: 0xFFFD125D
ROM CMT dwAddr: 0x10004FF0
ROM CMT dwLength: 0x00627837
Seems ROM Initialized OK!
Transmission Mode Requested: Control USB, Accepted: Control USB
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0020006800000031, ST, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x0020006800000031, ST, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00200068 (ST), Size: 1024MBytes, VPP: Not Supported
FlashChip 0x00200068 (ST), Size: 1024MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Transmission Mode Requested: Bulk USB, Accepted: Bulk USB
Box TX2 Data Pin set to: Service Pin 3
Waiting for FUR Client become avaiable...
[Nokia USB Flashing Generic]: Port opened OK!
FUR Avaiable!
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Overriding VPP Setting, USB can't use VPP
Box VPP disabled
Internal CMT Phone VPP Enabled
Warning: PAPUBKEYS Hash Missing!
APE Subsystem Not Found
CMT NPC Not Found
CMT CCC Not Found
CMT HWC Not Found
CMT VARIANT Not Found
CMT PARTNERC Not Found
Restarting MCU...
RPL Saved OK
RPL backup thread finished, continuing...
Pre flash tasks finished, continuing...
Processing RM-718_025.007_79.92_prd.core.fpsx (CMT)...
Booting CMT...
[Nokia USB Flashing Generic]: Port opened OK!
Old ROM Detected
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102031104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		26200217F7DC03442FDD9D537AC049A64CB54B81
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	916F75217F32081248B15C38DFC8E81B
CMT_BOOT_ROM_CRC:	E693EF0D
CMT_SECURE_ROM_CRC:	AC22615B
CMT Ready!
RM-718_025.007_79.92_prd.core.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Using NEW BB5 FLASHING PROTOCOL
Waiting for USB Boot ROM Answer...
ROM Ret: 0xFFFD125D
ROM CMT dwAddr: 0x10004FF0
ROM CMT dwLength: 0x00627837
Seems ROM Initialized OK!
Transmission Mode Requested: Control USB, Accepted: Control USB
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0020006800000031, ST, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x0020006800000031, ST, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00200068 (ST), Size: 1024MBytes, VPP: Not Supported
FlashChip 0x00200068 (ST), Size: 1024MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Transmission Mode Requested: Bulk USB, Accepted: Bulk USB
Box TX2 Data Pin set to: Service Pin 3
Waiting for FUR Client become avaiable...
[Nokia USB Flashing Generic]: Port opened OK!
FUR Avaiable!
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Overriding VPP Setting, USB can't use VPP
Box VPP disabled
Internal CMT Phone VPP Enabled
Warning: PAPUBKEYS Hash Missing!
Sending Certificates...
Certificates OK
Partitioning...
Partitioning OK
Started group flash erase
EraseArea[0,CMT]: 0x00040000-0x0007FFFF, ONENAND
EraseArea[0,CMT]: 0x000C0000-0x008BFFFF, ONENAND
EraseArea[0,CMT]: 0x00DC0000-0x0DAFFFFF, ONENAND
EraseArea[0,CMT]: 0x2E100000-0x3E5FFFFF, ONENAND
Erase Partition (CMT)
Waiting 320s for erasure finish...
Erase taken 4.296s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT ADA Certificate...
Writing CMT KEYS Certificate...
Writing CMT PRIMAPP Certificate...
Writing CMT RAP3NAND Certificate...
Writing CMT SOS+PMML Certificate...
Writing CMT PASUBTOC Certificate...
WARNING: CMT PAPUBKEYS Hash is Empty, writing first found PAPUBKEYS
Writing CMT PAPUBKEYS Certificate...
Writing CMT GENIO_INIT Certificate...
Writing CMT SOS*UPDAPP Certificate...
Writing CMT SOS*DSP0 Certificate...
Writing CMT LDSP Certificate...
Writing CMT SOS*ISASW Certificate...
Writing CMT SOS+CORE Certificate...
Writing CMT SOS+ROFS1 Certificate...
Programming Status OK!
All blocks written OK! Time taken 21.62s
Flashing Speed: 43116,30 kBit/S
Processing RM-718_025.007_79.92_prd.core.fpsx (APE)...
Processing RM-718_025.007_08.01_Hebrew_79.92_prd.rofs2.fpsx (CMT)...
RM-718_025.007_08.01_Hebrew_79.92_prd.rofs2.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
PAPUBKEYS Hash for CMT: C436DE8B3DEA6D6C6CCE9CBE15F7C501BB822D02
Started group flash erase
EraseArea[0,CMT]: 0x090C0000-0x0CBFFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.532s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS+ROFS2 Certificate...
Programming Status OK!
All blocks written OK! Time taken 8.172s
Flashing Speed: 51130,33 kBit/S
Processing RM-718_025.007_08.01_Hebrew_79.92_prd.rofs2.fpsx (APE)...
Processing RM-718_025.007_00.01_79.92_prd.rofs3.fpsx (CMT)...
RM-718_025.007_00.01_79.92_prd.rofs3.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
PAPUBKEYS Hash for CMT: C436DE8B3DEA6D6C6CCE9CBE15F7C501BB822D02
Started group flash erase
EraseArea[0,CMT]: 0x0CC00000-0x0DAFFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.156s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS+ROFS3 Certificate...
Programming Status OK!
All blocks written OK! Time taken 0.250s
Flashing Speed: 157,18 kBit/S
Processing RM-718_025.007_00.01_79.92_prd.rofs3.fpsx (APE)...
Processing RM-718_025.007_01.01_79.92.uda.fpsx (CMT)...
RM-718_025.007_01.01_79.92.uda.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
PAPUBKEYS Hash for CMT: C436DE8B3DEA6D6C6CCE9CBE15F7C501BB822D02
Started group flash erase
EraseArea[0,CMT]: 0x0DB00000-0x2E0FFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 4.610s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Programming Status OK!
All blocks written OK! Time taken 21.343s
Flashing Speed: 52073,13 kBit/S
Processing RM-718_025.007_01.01_79.92.uda.fpsx (APE)...
Processing RM601_APE_ONLY_ENO_11wk15_PS2_v0.063.fpsx (CMT)...
RM601_APE_ONLY_ENO_11wk15_PS2_v0.063.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
PAPUBKEYS Hash for CMT: C436DE8B3DEA6D6C6CCE9CBE15F7C501BB822D02
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x008C0000-0x00DBFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.62s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS*ENO Certificate...
Programming Status OK!
All blocks written OK! Time taken 1.31s
Flashing Speed: 38522,29 kBit/S
Processing RM601_APE_ONLY_ENO_11wk15_PS2_v0.063.fpsx (APE)...
Restarting MCU...
All images processed OK! Processing post flash tasks...
Setting Factory Defaults...
[Nokia C6-01 USB Phonet]: Port opened OK!
[Nokia C6-01 USB Phonet]: Port opened OK!
[Nokia C6-01 USB Phonet]: Port opened OK!
[Nokia C6-01 USB Phonet]: Port opened OK!
[Nokia C6-01 USB Phonet]: Port opened OK!
Factory defaults OK
Reading info...
[Nokia C6-01 USB Phonet]: Port opened OK!
MCU Version	V 92_11w37
MCU Date	14-09-11
Product		RM-601 (Nokia C6-01)
Manufacturer	(c) Nokia
IMEI		12345610654321?
IMEI Spare	1A32541660452301
IMEI SV		1332541660452321F1000000
PSN		0
PSD		0000000000000000
LPSN		0
APE SW		025.007
APE Variant	025.007025.007.08.01025.007.00.01
APE Test		0.063
APE HW		256
APE ADSP	256
APE BT		HCI Version 4 (rev. 0). LMP Version 4 (rev. 7455). Manufacturer 13.
RETU		40
TAHVO		00
AHNE		11
RFIC		|Alli_4.3.4
DSP		92_11w36
Failed to read info -> Failed to read SP info
Read info thread finished, continuing...
Post flash tasks finished!
Flashing successfully finished!

после всего этого телефон включился Но при проверки имей пишет серийный номер но там нет ни каких цифр- пусто,а ниже ок
Он ведь должен писать 123456....
Телефон без СИМ запускается в меню можно заходить. При включении с СИМ пишет SIM-карта недействительна
RPL устранить эту проблему?