Connect phone on selected interface...
UFS S/N 84238 boot - Ok
Connect phone on selected interface...
Core version : 1.22 , Rev : 4.5
Selected FlashSettings : Manual
Files Set for Flashing :
MCU : rm495__07.95.mcusw
PPM : rm495__07.95.ppm_ei
CNT : rm495__07.95.image_ei_blu
Check FlashFiles, Please, wait...
-> SWversion check skipped : Dead mode selected
Backup enabled, Will read Certificates now...
Setting FlashMode
FlashMode set Ok
1st boot Ok, C0
CMT part info :
CMT ASICID : 000000010000022600010006030C192101033000
CMT EM0 ID : 00000296
CMT EM1 ID : 00000B22
CMT PUB ID : 18900008D6B98A56834EDF3EAC0B8333809E54EA
CMT MODE ID : 00
CMT R_HASH : 9DDBFCFE6E73CED7D8C6268C8EB85723
CMT ROM ID : 273F6D55DFAAF68F
CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg , Rev : 0.0 Ver : 10.42.0
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 003F0001 , CMT , NOR
CMT Flash ID : 003F0001 < SPANSION => 72NS512P
FLCNT : 000000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo.fg , Rev : 0.0 Ver : 10.40.0
CMT Algo sent
PAPUBkeys blank (erased or HW failure)
Transmission mode : Dual (Ddr, TX2)
Boot Done!
CMT : Read NPC certificate...
Cert size : 0 byte(s)
CMT : Read CCC certificate...
Cert size : 0 byte(s)
CMT : Read HWC certificate...
Cert size : 0 byte(s)
CMT : Read VARIANT certificate...
Cert size : 0 byte(s)
No any CRT data (MCU damaged/CERT erased), skip saving
Init Service mode... Wait...
Init Service Mode Failed!
Setting FlashMode
FlashMode set Ok
1st boot Ok, C0
CMT part info :
CMT ASICID : 000000010000022600010006030C192101033000
CMT EM0 ID : 00000296
CMT EM1 ID : 00000B22
CMT PUB ID : 18900008D6B98A56834EDF3EAC0B8333809E54EA
CMT MODE ID : 00
CMT R_HASH : 9DDBFCFE6E73CED7D8C6268C8EB85723
CMT ROM ID : 273F6D55DFAAF68F
CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg , Rev : 0.0 Ver : 10.42.0
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 003F0001 , CMT , NOR
CMT Flash ID : 003F0001 < SPANSION => 72NS512P
FLCNT : 000000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo.fg , Rev : 0.0 Ver : 10.40.0
CMT Algo sent
PAPUBkeys blank (erased or HW failure)
Transmission mode : Dual (Ddr, TX2)
Boot Done!
Transmission mode : Dual (Ddr, TX2)
Erase : Processing rm495__07.95.mcusw
Found 6 areas to erase, erase group
Asic : CMT , Sub : NOR
CMT , NOR , Area : 0x00000000 - 0x000006BF
CMT , NOR , Area : 0x000006C0 - 0x0001FFFF
CMT , NOR , Area : 0x00040000 - 0x000BFFFF
CMT , NOR , Area : 0x000C0000 - 0x0013FFFF
CMT , NOR , Area : 0x00140000 - 0x0137FFFF
CMT , NOR , Area : 0x01380000 - 0x0151FFFF
Using TimeOut : 7 min ( 430 sec )
Erasing, wait.....
CMT : Group erase Ok
TIME : Erase time : 00:00:05
PrReq : NOR , 00
Transmission mode : Dual (Ddr, TX2)
Write : Processing rm495__07.95.mcusw
Error, 03, DataMissMatch, Check Cable, FlashPack, Firmware
Error write block at : 0
ERR : C7012D0103CD000090000000
Error on Flashing Phone!
Error...
Connect phone on selected interface...