GSM Форум www.UO5OQ.com

GSM Форум www.UO5OQ.com (https://www.uo5oq.com/forum/index.php)
-   BEST ( BB5 Easy Service Tool ) (https://www.uo5oq.com/forum/forumdisplay.php?f=35)
-   -   Обсуждение BB5 Easy Service Tool (https://www.uo5oq.com/forum/showthread.php?t=277)

Dimidrolus 31.07.2011 16:08
Обсуждение BB5 Easy Service Tool
 
Думаю все слышали про эту софтину. А у многих она уже есть. В этой теме можно будет задать вопрос по ней, спросить помощи в решение проблемы с ней и просто похвастаться тем, как вас распирает от радости приобритения этого продукта =) Собсно начну.

5530 после стирания через джаф:

Код:
Opening Connection...
Device Location: 00021134
Connect Ok!
Initializing Connection...
JAF Firmware: 01.B4
Authentificate JAF BOX...
TEA Authentication Completed...


JAF S/N ODU8PL2X boot - Ok
Switch jaf to FBUS...
Core version : 1.24 , Rev : 2.0

Selected FlashSettings : Manual
Files Set for Flashing :
MCU : RM-504_32.0.007_prd.core.C00
PPM : RM-504_32.0.007_prd.rofs2.V05
PPM2 : RM-504_32.0.007_C03_prd.rofs3.fpsx
CNT : RM-504_32.0.007_007_000_U001.uda.fpsx
Checking BUS...
Switch jaf to FlashMode...
FlashMode set Ok
Booting phone...

BOOT 1ST  : C0

CMT part info :
CMT ASICID  : 000000010000022600010006400C192101051105
CMT EM0 ID  : 00000296
CMT EM1 ID  : 00000B22
CMT PUB ID  : 18D00017C0800052DE6542BC53ED1800907880F1
CMT MODE ID : 00
CMT R_HASH  : B8C3ADECFC997FCD8081D3DEAF870B8C
CMT ROM ID  : 4B9B75103E691FF8

Change Protocol : NEW

Using NEW Flashing Protocol

CMT : Sending 2nd loader...
Use RAPIDOv11_2nd.fg  ,  Rev : 2.0  Ver : 9.48.0
CMT Loader sent, Boot Ok
Trans Req : 32 bit, DualLine, Set : 32 bit, DualLine
CMT Flash ID : 00400020 < ST => M39BORBOAD
FLIC : 00400020 , NAND , CMT

Sending Algo...
Use RAPIDOv11_XSR17_alg.fg  ,  Rev : 2.0  Ver : 9.48.0
Finalize done, Algo sent!
Trans Req : 32 bit, DualLine, Set : 32 bit, DualLine
PapubKeysReq : Blank (MCU erased or HW error)
Boot done!

CMT : Read NPC certificate...
CMT : Read CCC certificate...
CMT : Read HWC certificate...
No any CRT data (MCU damaged/CERT erased), skip saving


Checking BUS...
Switch jaf to FlashMode...
FlashMode set Ok
Booting phone...

BOOT 1ST  : C0

CMT part info :
CMT ASICID  : 000000010000022600010006400C192101051105
CMT EM0 ID  : 00000296
CMT EM1 ID  : 00000B22
CMT PUB ID  : 18D00017C0800052DE6542BC53ED1800907880F1
CMT MODE ID : 00
CMT R_HASH  : B8C3ADECFC997FCD8081D3DEAF870B8C
CMT ROM ID  : 4B9B75103E691FF8

Change Protocol : NEW

Using NEW Flashing Protocol

CMT : Sending 2nd loader...
Use RAPIDOv11_2nd.fg  ,  Rev : 2.0  Ver : 9.48.0
CMT Loader sent, Boot Ok
Trans Req : 32 bit, DualLine, Set : 32 bit, DualLine
CMT Flash ID : 00400020 < ST => M39BORBOAD
FLIC : 00400020 , NAND , CMT

Sending Algo...
Use RAPIDOv11_XSR17_alg.fg  ,  Rev : 2.0  Ver : 9.48.0
Finalize done, Algo sent!
Trans Req : 32 bit, DualLine, Set : 32 bit, DualLine
PapubKeysReq : Blank (MCU erased or HW error)
Boot done!

SC : StoreCert Ok

Partitioning....
Partitioning Ok...
Erase : Processing RM-504_32.0.007_prd.core.C00
Init Erase Mode Ok
Found 2 data types
Erasing Data....
Erase area : 0x00040000 - 0x00082FFF , CMT , NAND
Erase area : 0x00083400 - 0x003FFFFF , CMT , NAND
Erase area : 0x00400000 - 0x007FFFFF , CMT , NAND
Erase area : 0x00800000 - 0x00D5FFFF , CMT , NAND
Erase area : 0x00D60000 - 0x09E5FFFF , CMT , NAND
Erase Ok...
Erasing Partition....
Partition 0x0A
Erase Ok...
TIME : Erase time : 00:00:01
Write : Processing RM-504_32.0.007_prd.core.C00
Init Write Mode Ok
CMT: Writing Hash CERT [ADA]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [RAP3NAND]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [SOS*UPDAPP]
CMT: Writing Hash CERT [SOS*ENO]
CMT: Writing Hash CERT [SOS*DSP0]
CMT: Writing Hash CERT [SOS*ISASW]
CMT: Writing Hash CERT [SOS+CORE]
CMT: Writing Hash CERT [SOS+ROFS1]
Total writen 433 blocks
TIME : Write time : 00:07:49
PrReq : NAND , 000300000000020000000200000000

Erase : Processing RM-504_32.0.007_prd.rofs2.V05
Init Erase Mode Ok
Found 1 data types
Erasing Data....
Erase area : 0x07260000 - 0x0935FFFF , CMT , NAND
Erase Ok...
TIME : Erase time : 00:00:00
Write : Processing RM-504_32.0.007_prd.rofs2.V05
Init Write Mode Ok
CMT: Writing Hash CERT [SOS+ROFS2]
Total writen 114 blocks
TIME : Write time : 00:02:10
PrReq : NAND , 000300000000020000000200000000

Erase : Processing RM-504_32.0.007_C03_prd.rofs3.fpsx
Init Erase Mode Ok
Found 1 data types
Erasing Data....
Erase area : 0x09360000 - 0x09E5FFFF , CMT , NAND
Erase Ok...
TIME : Erase time : 00:00:00
Write : Processing RM-504_32.0.007_C03_prd.rofs3.fpsx
Init Write Mode Ok
CMT: Writing Hash CERT [SOS+ROFS3]
Total writen 24 blocks
TIME : Write time : 00:00:25
PrReq : NAND , 000300000000020000000200000000

ConvertImage: Processing RM-504_32.0.007_007_000_U001.uda.fpsx
ConvertImage: Page Size is 128K, no need convert
Erase : Processing RM-504_32.0.007_007_000_U001.uda.fpsx
Init Erase Mode Ok
Found 1 data types
Erasing Data....
Erase area : 0x09E60000 - 0x0F71FFFF , CMT , NAND
Erase Ok...
TIME : Erase time : 00:00:00
Write : Processing RM-504_32.0.007_007_000_U001.uda.fpsx
Init Write Mode Ok
Total writen 25 blocks
TIME : Write time : 00:00:29
PrReq : NAND , 000300000000020000000200000000

Switch jaf to FBUS...
FbusMode set Ok

Phone connected
Reading Phone Info....
Connected phone -  Nokia 5530 XpressMusic
Software Info:    V ICPR72_10w25.3
11-10-10
RM-504
(c) Nokia
IMEI:  12345610654321?
Ape Version: V 32.0.007
Product code: 
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Settings After Flash Defaults...
FullFactorySet...OK!
ProductTuneSet...OK!
SwUpgradeSet...OK!
AfterFlash operations done... Reconnect, wait...
Flashing done


Connect phone on selected interface...
n8 по usb:

Код:
Core version : 1.24 , Rev : 2.0

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : RM-596_013.016_79.92_prd.core.fpsx
PPM : RM-596_013.016_04.01_Russian_79.92_prd.rofs2.fpsx
PPM2 : RM-596_013.016_00.01_79.92_prd.rofs3.fpsx
CNT : RM-596_013.016_U01.01_79.92_prd.uda.fpsx
Flashing phone now...
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID:      000000030000022600010007600C192102031104
CPU ID :      RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID:        00000C35
EM1 ID:        00000C30
PUBLIC ID:    1370000CEED5034415098AC8F42FC94A867059C1
ASIC MODE ID:  00
ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B
ROM ID:        E693EF0DAC22615B
Use RAPUv11_2nd.fg  ,  Rev : 3.0  Ver : 11.24.0
Processing RAWLOADER...
FLIC : 005000EC
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg  ,  Rev : 3.0  Ver : 11.24.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
ADL: phone is in flash mode

Backup enabled, will read all certificates...
Reading NPC certificate...
IMEI : 356988049529601
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Cert Read done!

NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...

RPL saved : D:\Работа\Nokia\Софт\Best\Backup\Cert\356988049529601_CRT.rpl

  ===Flashing [MCU]===
Erase : Processing RM-596_013.016_79.92_prd.core.fpsx
Partitioning....
Partitioning Ok...
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:01
Write : Processing RM-596_013.016_79.92_prd.core.fpsx
CMT: Writing Hash CERT [ADA]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [RAP3NAND]
CMT: Writing Hash CERT [SOS+PMML]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [GENIO_INIT]
CMT: Writing Hash CERT [SOS*UPDAPP]
CMT: Writing Hash CERT [SOS*DSP0]
CMT: Writing Hash CERT [LDSP]
CMT: Writing Hash CERT [SOS*ISASW]
CMT: Writing Hash CERT [SOS+CORE]
CMT: Writing Hash CERT [SOS+ROFS1]
Total writen 548 blocks
TIME : Write time : 00:00:22
MCU Write done
ADL: Request programm status
NAND status : 00000004 / 00000004 / 00000000

  ===Flashing [PPM]===
Erase : Processing RM-596_013.016_04.01_Russian_79.92_prd.rofs2.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing RM-596_013.016_04.01_Russian_79.92_prd.rofs2.fpsx
CMT: Writing Hash CERT [SOS+ROFS2]
Total writen 178 blocks
TIME : Write time : 00:00:07
PPM Write done
ADL: Request programm status
NAND status : 00000004 / 00000004 / 00000000

  ===Flashing [PPM2]===
Erase : Processing RM-596_013.016_00.01_79.92_prd.rofs3.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing RM-596_013.016_00.01_79.92_prd.rofs3.fpsx
CMT: Writing Hash CERT [SOS+ROFS3]
Total writen 2 blocks
TIME : Write time : 00:00:00
PPM Write done
ADL: Request programm status
NAND status : 00000004 / 00000004 / 00000000

  ===Flashing [CNT]===
Erase : Processing RM-596_013.016_U01.01_79.92_prd.uda.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:01
Write : Processing RM-596_013.016_U01.01_79.92_prd.uda.fpsx
Total writen 216 blocks
TIME : Write time : 00:00:08
CNT Write done
ADL: Request programm status
NAND status : 00000004 / 00000004 / 00000000

ADL: Close_Session
Content: 000300000000040000000400000000
ADL: Reboot

Flashing done!
Total flash time : 00:00:43
Reboot phone now...

Reading Phone Info....
Connected phone -  Nokia N8-00
Software Info:    V 92PS1_10w46.7 26-01-11 RM-596 (c) Nokia
IMEI:  356988049529601
Ape Version: 013.016
Product code:  059C2K8
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Settings After Flash Defaults...
FullFactorySet...OK!
ProductTuneSet...OK!
SwUpgradeSet...OK!
Product code update...
Set phone to Normal mode...
AfterFlash operations done...
Done!

Elapsed: 00:01:20
Connect phone on selected interface...

:)

Dimidrolus 28.10.2011 14:18
Re: Обсуждение BB5 Easy Service Tool
 
x7 usb)
Код:
Selected FlashSettings : Manual
->  File : RM-707_021.013_00.01_79.92_prd.rofs3.fpsx not found! Check it!
->  File : RM-707_021.013_U01.01_79.92.uda.fpsx not found! Check it!
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : RM-707_021.013_79.92_prd.core.fpsx
PPM : RM-707_021.013_04.01_Russian_79.92_prd.rofs2.fpsx
Flashing phone now...
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID:      000000030000022600010007600C192102031104
CPU ID :      RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID:        00000C35
EM1 ID:        00000C30
PUBLIC ID:    0820010661F758400B3044B9AAFEC26AF4BE6B72
ASIC MODE ID:  00
ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B
ROM ID:        E693EF0DAC22615B
Use RAPUv11_2nd.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing RAWLOADER...
FLIC : 006000EC
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : A777258432D3E9101D6160DBAC2702FCC602E752
ADL: phone is in flash mode

Backup enabled, will read all certificates...
Reading NPC certificate...
IMEI : 356257048188342
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Reading PARTNERC certificate...
Reading MDM_KEYS certificate...
Cert Read done!

NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...

RPL saved : D:\Ðàáîòà\Nokia\Ñîôò\Best\Backup\Cert\356257048188342_CRT.rpl

  ===Flashing [MCU]===
Erase : Processing RM-707_021.013_79.92_prd.core.fpsx
Partitioning....
Partitioning Ok...
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:02
Write : Processing RM-707_021.013_79.92_prd.core.fpsx
CMT: Writing Hash CERT [ADA]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [RAP3NAND]
CMT: Writing Hash CERT [SOS+PMML]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [GENIO_INIT]
CMT: Writing Hash CERT [SOS*UPDAPP]
CMT: Writing Hash CERT [SOS*DSP0]
CMT: Writing Hash CERT [LDSP]
CMT: Writing Hash CERT [SOS*ISASW]
CMT: Writing Hash CERT [SOS+CORE]
CMT: Writing Hash CERT [SOS+ROFS1]
Total writen 505 blocks
TIME : Write time : 00:00:21
MCU Write done
ADL: Request programm status
NAND status : 00000001 / 00000001 / 00000000

  ===Flashing [PPM]===
Erase : Processing RM-707_021.013_04.01_Russian_79.92_prd.rofs2.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing RM-707_021.013_04.01_Russian_79.92_prd.rofs2.fpsx
CMT: Writing Hash CERT [SOS+ROFS2]
Total writen 196 blocks
TIME : Write time : 00:00:08
PPM Write done
ADL: Request programm status
NAND status : 00000001 / 00000001 / 00000000

ADL: Close_Session
Content: 000300000000010000000100000000
ADL: Reboot

Flashing done!
Total flash time : 00:00:32
Reboot phone now...

Reading Phone Info....
Connected phone -  Nokia X7-00
Software Info:    V 92_11w15.4 17-05-11 RM-707 (c) Nokia
IMEI:  356257048188342
Ape Version: 021.013
Product code:  059H3L9
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Settings After Flash Defaults...
ProductTuneSet...OK!
SwUpgradeSet...OK!
AfterFlash operations done ;D
Done!

Elapsed: 00:00:54
Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info...  - Ok
:)

Dimidrolus 08.12.2011 15:15
Re: Обсуждение BB5 Easy Service Tool
 
e52) Нету локала) Стирка нпц помогла)

Код:
Connect phone on selected interface...

Core version : 1.30  Rev : 1.1

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm469_052.003_prd.core.fpsx
PPM : rm469_052.003_05.01_Russian_prd.rofs2.fpsx
PPM2 : rm469_052.003_C00.01_DEFAULT_prd.rofs3.fpsx
CNT : RM469_ENO_09w23v0.a078.01.fpsx
APE : rm469_052.003_U007.000_prd.uda.fpsx
Flashing phone now...
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID:      000000030000022600010007600C192102011104
CPU ID :      RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID:        00001040
EM1 ID:        00001030
PUBLIC ID:    26A00102A58C0344C6799167A76D6F1D48E1D915
ASIC MODE ID:  00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID:        3E273BF637BE26FA
Use RAPUv11_2nd.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing RAWLOADER...
FLIC : 00400020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:03
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : 85F252E351E225CAFC4DFBC8041EABD2823E3500
ADL: phone is in flash mode
  ===Flashing [MCU]===
Erase : Processing rm469_052.003_prd.core.fpsx
Partitioning....
Partitioning Ok...
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:01
Write : Processing rm469_052.003_prd.core.fpsx
CMT: Writing Hash CERT [ADA]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [RAP3NAND]
CMT: Writing Hash CERT [SOS+PMML]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [GENIO_INIT]
CMT: Writing Hash CERT [SOS*UPDAPP]
CMT: Writing Hash CERT [SOS*DSP0]
CMT: Writing Hash CERT [LDSP]
CMT: Writing Hash CERT [SOS*ISASW]
CMT: Writing Hash CERT [SOS+CORE]
CMT: Writing Hash CERT [SOS+ROFS1]
Total writen 428 blocks
TIME : Write time : 00:00:23
MCU Write done
ADL: Request programm status
NAND status : 00000028 / 00000001 / 00000000

  ===Flashing [PPM]===
Erase : Processing rm469_052.003_05.01_Russian_prd.rofs2.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm469_052.003_05.01_Russian_prd.rofs2.fpsx
CMT: Writing Hash CERT [SOS+ROFS2]
Total writen 166 blocks
TIME : Write time : 00:00:09
PPM Write done
ADL: Request programm status
NAND status : 00000028 / 00000001 / 00000000

  ===Flashing [PPM2]===
Erase : Processing rm469_052.003_C00.01_DEFAULT_prd.rofs3.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm469_052.003_C00.01_DEFAULT_prd.rofs3.fpsx
CMT: Writing Hash CERT [SOS+ROFS3]
Total writen 32 blocks
TIME : Write time : 00:00:01
PPM Write done
ADL: Request programm status
NAND status : 00000028 / 00000001 / 00000000

  ===Flashing [CNT]===
Erase : Processing RM469_ENO_09w23v0.a078.01.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing RM469_ENO_09w23v0.a078.01.fpsx
CMT: Writing Hash CERT [SOS*ENO]
Total writen 12 blocks
TIME : Write time : 00:00:00
CNT Write done
ADL: Request programm status
NAND status : 00000028 / 00000001 / 00000000

  ===Flashing [APE]===
Erase : Processing rm469_052.003_U007.000_prd.uda.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm469_052.003_U007.000_prd.uda.fpsx
Total writen 15 blocks
TIME : Write time : 00:00:01
APE Write done
ADL: Request programm status
NAND status : 00000028 / 00000001 / 00000000

ADL: Close_Session
Content: 000300000000280000000100000000
ADL: Reboot

Flashing done!
Total flash time : 00:00:38
Reboot phone now...

 - > AfterFlash Failed! :( Reason : Downgrade try or HW Error
    Anyway - try reinsert battery and PowerUp phone manualy

Connect phone on selected interface...

Done!

Elapsed: 00:02:43
Connect phone on selected interface...

Backup Certificates now...
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID:      000000030000022600010007600C192102011104
CPU ID :      RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID:        00001040
EM1 ID:        00001030
PUBLIC ID:    26A00102A58C0344C6799167A76D6F1D48E1D915
ASIC MODE ID:  00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID:        3E273BF637BE26FA
Use RAPUv11_2nd.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing RAWLOADER...
FLIC : 00400020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : 85F252E351E225CAFC4DFBC8041EABD2823E3500
ADL: Reading certificates...

Reading NPC certificate...
IMEI : 353785041570408
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Reading PARTNERC certificate...
Reading MDM_KEYS certificate...
Cert Read done!

ADL: Reading certificates done! :)
ADL: Close_Session
Content: 000300000000280000000100000000
ADL: Reboot

Wait, reconneting...

- > Phone not found... :(
- > CertRead failed : phone was not bootup
- > Connection/SW/HW problem, try bootup manually

Phone disconected!

Connect phone on selected interface...

Backup Certificates now...
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID:      000000030000022600010007600C192102011104
CPU ID :      RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID:        00001040
EM1 ID:        00001030
PUBLIC ID:    26A00102A58C0344C6799167A76D6F1D48E1D915
ASIC MODE ID:  00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID:        3E273BF637BE26FA
Use RAPUv11_2nd.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing RAWLOADER...
FLIC : 00400020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : 85F252E351E225CAFC4DFBC8041EABD2823E3500
ADL: Reading certificates...

Reading NPC certificate...
IMEI : 353785041570408
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Reading PARTNERC certificate...
Reading MDM_KEYS certificate...
Cert Read done!

ADL: Reading certificates done! :)
ADL: Close_Session
Content: 000300000000280000000100000000
ADL: Reboot

Wait, reconneting...

- > Phone not found... :(
- > CertRead failed : phone was not bootup
- > Connection/SW/HW problem, try bootup manually

NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...

RPL saved : D:\Ðàáîòà\Nokia\Ñîôò\Best\Backup\Cert\353785041570408_CRT.rpl

Phone disconected!

Connect phone on selected interface...

Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID:      000000030000022600010007600C192102011104
CPU ID :      RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID:        00001040
EM1 ID:        00001030
PUBLIC ID:    26A00102A58C0344C6799167A76D6F1D48E1D915
ASIC MODE ID:  00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID:        3E273BF637BE26FA
Use RAPUv11_2nd.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing RAWLOADER...
FLIC : 00400020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : 85F252E351E225CAFC4DFBC8041EABD2823E3500
ADL: Preparing for erase certificates...

Erase NPC... Ok
Erase CCC... Ok
Erase HWC... Ok

ADL: Erase Flash certs done! :)

ADL: Close_Session
Content: 000300000000280000000100000000
ADL: Reboot
Done!

Phone disconected!

Connect phone on selected interface...

Core version : 1.30  Rev : 1.1

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm469_052.003_prd.core.fpsx
PPM : rm469_052.003_05.01_Russian_prd.rofs2.fpsx
PPM2 : rm469_052.003_C00.01_DEFAULT_prd.rofs3.fpsx
CNT : RM469_ENO_09w23v0.a078.01.fpsx
APE : rm469_052.003_U007.000_prd.uda.fpsx
Flashing phone now...
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID:      000000030000022600010007600C192102011104
CPU ID :      RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID:        00001040
EM1 ID:        00001030
PUBLIC ID:    26A00102A58C0344C6799167A76D6F1D48E1D915
ASIC MODE ID:  00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID:        3E273BF637BE26FA
Use RAPUv11_2nd.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing RAWLOADER...
FLIC : 00400020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : 85F252E351E225CAFC4DFBC8041EABD2823E3500
ADL: phone is in flash mode
  ===Flashing [MCU]===
Erase : Processing rm469_052.003_prd.core.fpsx
Partitioning....
Partitioning Ok...
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:01
Write : Processing rm469_052.003_prd.core.fpsx
CMT: Writing Hash CERT [ADA]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [RAP3NAND]
CMT: Writing Hash CERT [SOS+PMML]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [GENIO_INIT]
CMT: Writing Hash CERT [SOS*UPDAPP]
CMT: Writing Hash CERT [SOS*DSP0]
CMT: Writing Hash CERT [LDSP]
CMT: Writing Hash CERT [SOS*ISASW]
CMT: Writing Hash CERT [SOS+CORE]
CMT: Writing Hash CERT [SOS+ROFS1]
Total writen 428 blocks
TIME : Write time : 00:00:22
MCU Write done
ADL: Request programm status
NAND status : 00000028 / 00000001 / 00000000

  ===Flashing [PPM]===
Erase : Processing rm469_052.003_05.01_Russian_prd.rofs2.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm469_052.003_05.01_Russian_prd.rofs2.fpsx
CMT: Writing Hash CERT [SOS+ROFS2]
Total writen 166 blocks
TIME : Write time : 00:00:09
PPM Write done
ADL: Request programm status
NAND status : 00000028 / 00000001 / 00000000

  ===Flashing [PPM2]===
Erase : Processing rm469_052.003_C00.01_DEFAULT_prd.rofs3.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm469_052.003_C00.01_DEFAULT_prd.rofs3.fpsx
CMT: Writing Hash CERT [SOS+ROFS3]
Total writen 32 blocks
TIME : Write time : 00:00:01
PPM Write done
ADL: Request programm status
NAND status : 00000028 / 00000001 / 00000000

  ===Flashing [CNT]===
Erase : Processing RM469_ENO_09w23v0.a078.01.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing RM469_ENO_09w23v0.a078.01.fpsx
CMT: Writing Hash CERT [SOS*ENO]
Total writen 12 blocks
TIME : Write time : 00:00:00
CNT Write done
ADL: Request programm status
NAND status : 00000028 / 00000001 / 00000000

  ===Flashing [APE]===
Erase : Processing rm469_052.003_U007.000_prd.uda.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm469_052.003_U007.000_prd.uda.fpsx
Total writen 15 blocks
TIME : Write time : 00:00:01
APE Write done
ADL: Request programm status
NAND status : 00000028 / 00000001 / 00000000

ADL: Close_Session
Content: 000300000000280000000100000000
ADL: Reboot

Flashing done!
Total flash time : 00:00:37
Reboot phone now...

Reading Phone Info....
Connected phone -  Nokia E52-1
Software Info:    V ICPR82_10w22.3 12-10-10 RM-469 (c) Nokia
IMEI:  12345610654321?
Ape Version: 052.003
Product code:  0578052
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Settings After Flash Defaults...
FullFactorySet...OK!
ProductTuneSet...OK!
SwUpgradeSet...OK!
AfterFlash operations done ;D
Done!

Elapsed: 00:01:02
Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info...  - Ok

Backup Certificates now...
Backup CRT308 data...
CRT308 Backup Created
SLx Simlock Data read ... ok
SL3 Simlock Sign read ... ok
WMDRM read ... ok
Check communication with phone....
Reboot....
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID:      000000030000022600010007600C192102011104
CPU ID :      RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID:        00001040
EM1 ID:        00001030
PUBLIC ID:    26A00102A58C0344C6799167A76D6F1D48E1D915
ASIC MODE ID:  00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID:        3E273BF637BE26FA
Use RAPUv11_2nd.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing RAWLOADER...
FLIC : 00400020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:04
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : 85F252E351E225CAFC4DFBC8041EABD2823E3500
ADL: Reading certificates...

Reading NPC certificate...
IMEI : 000000000000000
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Reading PARTNERC certificate...
Reading MDM_KEYS certificate...
Cert Read done!

ADL: Reading certificates done! :)
ADL: Close_Session
Content: 000300000000280000000100000000
ADL: Reboot

SimLock Data saved...
SimLock Key saved...
WMDRM_PD Data saved...

RPL saved : D:\Ðàáîòà\Nokia\Ñîôò\Best\Backup\Cert\000000000000000_SIM.rpl

All done, Disconnecting

Elapsed: 00:00:10
Connect phone on selected interface...


Phone found!
Series 60 Device detected!
read info...  - Ok

User ACCEPTED FULL ERASE
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID:      000000030000022600010007600C192102011104
CPU ID :      RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID:        00001040
EM1 ID:        00001030
PUBLIC ID:    26A00102A58C0344C6799167A76D6F1D48E1D915
ASIC MODE ID:  00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID:        3E273BF637BE26FA
Use RAPUv11_2nd.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing RAWLOADER...
FLIC : 00400020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:05
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : 85F252E351E225CAFC4DFBC8041EABD2823E3500
ADL: Preparing for erase...

Full Erase started...
Asic : CMT , Sub : NAND
Erase Area 0x00000000-0x0FFFFFFF
Erasing Ok , [0F]
Erase done , time : 00:00:01

ADL: Erase done

ADL: Close_Session
Content: 000205000000000000FFFF00000000
ADL: Reboot
Phone disconected!

Connect phone on selected interface...

Core version : 1.30  Rev : 1.1

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm469_052.003_prd.core.fpsx
PPM : rm469_052.003_05.01_Russian_prd.rofs2.fpsx
PPM2 : rm469_052.003_C00.01_DEFAULT_prd.rofs3.fpsx
CNT : RM469_ENO_09w23v0.a078.01.fpsx
APE : rm469_052.003_U007.000_prd.uda.fpsx
Flashing phone now...
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID:      000000030000022600010007600C192102011104
CPU ID :      RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID:        00001040
EM1 ID:        00001030
PUBLIC ID:    26A00102A58C0344C6799167A76D6F1D48E1D915
ASIC MODE ID:  00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID:        3E273BF637BE26FA
Use RAPUv11_2nd.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing RAWLOADER...
FLIC : 00400020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : blank (Erased or HW failure)
ADL: phone is in flash mode
  ===Flashing [MCU]===
Erase : Processing rm469_052.003_prd.core.fpsx
Partitioning....
Partitioning Ok...
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:01
Write : Processing rm469_052.003_prd.core.fpsx
CMT: Writing Hash CERT [ADA]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [RAP3NAND]
CMT: Writing Hash CERT [SOS+PMML]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [GENIO_INIT]
CMT: Writing Hash CERT [SOS*UPDAPP]
CMT: Writing Hash CERT [SOS*DSP0]
CMT: Writing Hash CERT [LDSP]
CMT: Writing Hash CERT [SOS*ISASW]
CMT: Writing Hash CERT [SOS+CORE]
CMT: Writing Hash CERT [SOS+ROFS1]
Total writen 428 blocks
TIME : Write time : 00:00:22
MCU Write done
ADL: Request programm status
NAND status : 00000028 / 00000001 / 00000000

  ===Flashing [PPM]===
Erase : Processing rm469_052.003_05.01_Russian_prd.rofs2.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm469_052.003_05.01_Russian_prd.rofs2.fpsx
CMT: Writing Hash CERT [SOS+ROFS2]
Total writen 166 blocks
TIME : Write time : 00:00:09
PPM Write done
ADL: Request programm status
NAND status : 00000028 / 00000001 / 00000000

  ===Flashing [PPM2]===
Erase : Processing rm469_052.003_C00.01_DEFAULT_prd.rofs3.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm469_052.003_C00.01_DEFAULT_prd.rofs3.fpsx
CMT: Writing Hash CERT [SOS+ROFS3]
Total writen 32 blocks
TIME : Write time : 00:00:01
PPM Write done
ADL: Request programm status
NAND status : 00000028 / 00000001 / 00000000

  ===Flashing [CNT]===
Erase : Processing RM469_ENO_09w23v0.a078.01.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing RM469_ENO_09w23v0.a078.01.fpsx
CMT: Writing Hash CERT [SOS*ENO]
Total writen 12 blocks
TIME : Write time : 00:00:00
CNT Write done
ADL: Request programm status
NAND status : 00000028 / 00000001 / 00000000

  ===Flashing [APE]===
Erase : Processing rm469_052.003_U007.000_prd.uda.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm469_052.003_U007.000_prd.uda.fpsx
Total writen 15 blocks
TIME : Write time : 00:00:01
APE Write done
ADL: Request programm status
NAND status : 00000028 / 00000001 / 00000000

ADL: Close_Session
Content: 000300000000280000000100000000
ADL: Reboot

Flashing done!
Total flash time : 00:00:36
Reboot phone now...

Reading Phone Info....
Connected phone -  Nokia E52-1
Software Info:    V ICPR82_10w22.3 12-10-10 RM-469 (c) Nokia
IMEI:  12345610654321?
Ape Version: 052.003
Product code: 
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Settings After Flash Defaults...
FullFactorySet...OK!
ProductTuneSet...OK!
SwUpgradeSet...OK!
AfterFlash operations done ;D
Done!

Elapsed: 00:00:54
Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info...  - Ok

Will Write RPL keys now...
Check RPL file...
SimLock Data found!
SimLock key found!
WMDRM key found!
-> Skip Flash keys Part, for Flash Part use Dead Mode or Fbus
Check phone mode...
Phone in Local mode
Seting Test mode... wait...
Test mode set

Writing SimLock Key...  Error!
Writing SimLock Data...  Error!

SDD Key status : SDData Damaged!!!!! :(
SimLock status : SimLock is Ok
Security status : Security is Ok

WMDRM_PD key sent... Ok

Done!

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info...  - Ok

Will Write RPL keys now...
Check RPL file...
NPC Data found! (CMT)
CCC Data found! (CMT)
HWC Data found! (CMT)
-> Skip Flash keys Part, for Flash Part use Dead Mode or Fbus

Done!

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info...  - Ok

Reading Phone Info....
Connected phone -    Nokia E52-1
Software ver : V ICPR82_10w22.3 12-10-10 RM-469 (c) Nokia
IMEI    :      12345610654321?
Ape Ver :      052.003
APE Var :      052.003052.003.05.01052.003.C00.01
APE ADSP:      256
DSP Ver :      ICPR82_10w22_RIO
APE Test:      RM469_ENO_09w23v0.a078.01
PPM    :     
CNT    :     
Product SN  :    0
Product code :   
Base Prd.code:   
Module code  :   
Long Prod.SN :    0
Hardware info=======
HWID  :
Retu  : 40
Tahvo : 00
Batery: 3632 mV
Camera:
CMT BT:
APE BT:
APE HW: 256
LCDVer:
RF ic :
Lock info ===========
IMEI      : 12345610654321?
IMEI spNet : 1A 32 54 16 60 45 23 01
IMEI svNet : 13 32 54 16 60 45 23 41 F9

Unable to read Lock table... :(

IMEI data damaged, CRT save skipped... :(

User code : Crypted
UserDataExLevel : Low [Gallery]

Done!

Will Write RPL keys now...
Check RPL file...
NPC Data found! (CMT)
CCC Data found! (CMT)
HWC Data found! (CMT)
-> Skip Flash keys Part, for Flash Part use Dead Mode or Fbus

Done!

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info...  - Ok

Phone disconected!

Connect phone on selected interface...

Will Write RPL keys now...
Check RPL file...
NPC Data found! (CMT)
CCC Data found! (CMT)
HWC Data found! (CMT)
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID:      000000030000022600010007600C192102011104
CPU ID :      RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID:        00001040
EM1 ID:        00001030
PUBLIC ID:    26A00102A58C0344C6799167A76D6F1D48E1D915
ASIC MODE ID:  00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID:        3E273BF637BE26FA
Use RAPUv11_2nd.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing RAWLOADER...
FLIC : 00400020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:03
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : 85F252E351E225CAFC4DFBC8041EABD2823E3500
ADL: Preparing for write certificates...

Erase NPC... Ok
Writing NPC... Ok
Erase CCC... Ok
Writing CCC... Ok
Erase HWC... Ok
Writing HWC... Ok

ADL: Writing Flash certs done! :)

ADL: Close_Session
Content: 000300000000280000000100000000
ADL: Reboot

-> No any Flex keys selected, skip flex part

Done!

Phone disconected!

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info...  - Ok

Reading Phone Info....
Connected phone -    Nokia E52-1
Software ver : V ICPR82_10w22.3 12-10-10 RM-469 (c) Nokia
IMEI    :      353785041570408
Ape Ver :      052.003
APE Var :      052.003052.003.05.01052.003.C00.01
APE ADSP:      256
DSP Ver :      ICPR82_10w22_RIO
APE Test:      RM469_ENO_09w23v0.a078.01
PPM    :     
CNT    :     
Product SN  :    0
Product code :   
Base Prd.code:   
Module code  :   
Long Prod.SN :    0
Hardware info=======
HWID  :
Retu  : 40
Tahvo : 00
Batery: 3647 mV
Camera:
CMT BT:
APE BT:
APE HW: 256
LCDVer:
RF ic :
Lock info ===========
IMEI      : 353785041570408
IMEI spNet : 3A 35 87 05 14 75 40 00
IMEI svNet : 33 35 87 05 14 75 40 40 F9

Unable to read Lock table... :(
CRT308 Backup Created

User code : Crypted
UserDataExLevel : Low [Gallery]

Done!

Reading Phone Info....
Connected phone -    Nokia E52-1
Software ver : V ICPR82_10w22.3 12-10-10 RM-469 (c) Nokia
IMEI    :      353785041570408
Ape Ver :      052.003
APE Var :      052.003052.003.05.01052.003.C00.01
APE ADSP:      256
DSP Ver :      ICPR82_10w22_RIO
APE Test:      RM469_ENO_09w23v0.a078.01
PPM    :     
CNT    :     
Product SN  :    0
Product code :   
Base Prd.code:   
Module code  :   
Long Prod.SN :    0
Hardware info=======
HWID  :
Retu  : 40
Tahvo : 00
Batery: 3629 mV
Camera:
CMT BT:
APE BT:
APE HW: 256
LCDVer:
RF ic :
Lock info ===========
IMEI      : 353785041570408
IMEI spNet : 3A 35 87 05 14 75 40 00
IMEI svNet : 33 35 87 05 14 75 40 40 F9

Unable to read Lock table... :(
CRT308 Backup Created

User code : Crypted
UserDataExLevel : Low [Gallery]

Done!

Reading Phone Info....
Connected phone -    Nokia E52-1
Software ver : V ICPR82_10w22.3 12-10-10 RM-469 (c) Nokia
IMEI    :      353785041570408
Ape Ver :      052.003
APE Var :      052.003052.003.05.01052.003.C00.01
APE ADSP:      256
DSP Ver :      ICPR82_10w22_RIO
APE Test:      RM469_ENO_09w23v0.a078.01
PPM    :     
CNT    :     
Product SN  :    0
Product code :   
Base Prd.code:   
Module code  :   
Long Prod.SN :    0
Hardware info=======
HWID  :
Retu  : 40
Tahvo : 00
Batery: 3629 mV
Camera:
CMT BT:
APE BT:
APE HW: 256
LCDVer:
RF ic :
Lock info ===========
IMEI      : 353785041570408
IMEI spNet : 3A 35 87 05 14 75 40 00
IMEI svNet : 33 35 87 05 14 75 40 40 F9

Unable to read Lock table... :(
CRT308 Backup Created

User code : Crypted
UserDataExLevel : Low [Gallery]

Done!

Reading Phone Info....
Connected phone -    Nokia E52-1
Software ver : V ICPR82_10w22.3 12-10-10 RM-469 (c) Nokia
IMEI    :      353785041570408
Ape Ver :      052.003
APE Var :      052.003052.003.05.01052.003.C00.01
APE ADSP:      256
DSP Ver :      ICPR82_10w22_RIO
APE Test:      RM469_ENO_09w23v0.a078.01
PPM    :     
CNT    :     
Product SN  :    0
Product code :   
Base Prd.code:   
Module code  :   
Long Prod.SN :    0
Hardware info=======
HWID  :
Retu  : 40
Tahvo : 00
Batery: 3627 mV
Camera:
CMT BT:
APE BT:
APE HW: 256
LCDVer:
RF ic :
Lock info ===========
IMEI      : 353785041570408
IMEI spNet : 3A 35 87 05 14 75 40 00
IMEI svNet : 33 35 87 05 14 75 40 40 F9

Unable to read Lock table... :(
CRT308 Backup Created

User code : Crypted
UserDataExLevel : Low [Gallery]

Done!

Reading Phone Info....
Connected phone -    Nokia E52-1
Software ver : V ICPR82_10w22.3 12-10-10 RM-469 (c) Nokia
IMEI    :      353785041570408
Ape Ver :      052.003
APE Var :      052.003052.003.05.01052.003.C00.01
APE ADSP:      256
DSP Ver :      ICPR82_10w22_RIO
APE Test:      RM469_ENO_09w23v0.a078.01
PPM    :     
CNT    :     
Product SN  :    0
Product code :   
Base Prd.code:   
Module code  :   
Long Prod.SN :    0
Hardware info=======
HWID  :
Retu  : 40
Tahvo : 00
Batery: 3629 mV
Camera:
CMT BT:
APE BT:
APE HW: 256
LCDVer:
RF ic :
Lock info ===========
IMEI      : 353785041570408
IMEI spNet : 3A 35 87 05 14 75 40 00
IMEI svNet : 33 35 87 05 14 75 40 40 F9

Unable to read Lock table... :(
CRT308 Backup Created

User code : Crypted
UserDataExLevel : Low [Gallery]

Done!

Will Write RPL keys now...
Check RPL file...
SimLock Data found!
SimLock key found!
WMDRM key found!
-> Skip Flash keys Part, for Flash Part use Dead Mode or Fbus
Check phone mode...
Phone in Local mode
Seting Test mode... wait...
Test mode set

Writing SimLock Key...  Ok!
Writing SimLock Data...  Ok!

SDD Key status : SDData Damaged!!!!! :(
SimLock status : SimLock is Ok
Security status : Security is Ok

WMDRM_PD key sent... Ok

Done!

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info...  - Ok

Reading Phone Info....
Connected phone -    Nokia E52-1
Software ver : V ICPR82_10w22.3 12-10-10 RM-469 (c) Nokia
IMEI    :      353785041570408
Ape Ver :      052.003
APE Var :      052.003052.003.05.01052.003.C00.01
APE ADSP:      256
DSP Ver :      ICPR82_10w22_RIO
APE Test:      RM469_ENO_09w23v0.a078.01
PPM    :     
CNT    :     
Product SN  :    0
Product code :   
Base Prd.code:   
Module code  :   
Long Prod.SN :    0
Hardware info=======
HWID  :
Retu  : 40
Tahvo : 00
Batery: 3632 mV
Camera:
CMT BT:
APE BT:
APE HW: 256
LCDVer:
RF ic :
Lock info ===========
IMEI      : 353785041570408
IMEI spNet : 3A 35 87 05 14 75 40 00
IMEI svNet : 33 35 87 05 14 75 40 40 F9

Conf key    : 0000000000000000
Provider key : 2440700000000000
Provider    : AT&T;U.S.A. (3650)
Counters  : Key 0  [3] , Fbus 0  [10]
Blocks      : 7

LOCK STATUS :
=============================
BLK : 1
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 2
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 3
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 4
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 5
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 6
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 7
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
=============================
LOCKS :  All Open
=============================
CRT308 Backup Created

User code : Crypted
UserDataExLevel : Low [Gallery]

Done!

Repair SD procedure started...

Phone Imei: 353785041570408

 - >  Power Off phone, dissconnect it and connect

 - > Phone was not powered Off

Can't read Unique data! :(
Repair fail...!

Phone disconected!

Connect phone on selected interface...

Read Uniq key data started...

Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID:      000000030000022600010007600C192102011104
CPU ID :      RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
PUBLIC ID:    26A00102A58C0344C6799167A76D6F1D48E1D915
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
Fetching data, wait...

 - > Reinsert cable and battery, press powerOn button again
 - > For X7, E7 - just waiting, near 1 minute
 - > When BEST start Search Phone - Press PowerOn if needed

Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID:      000000030000022600010007600C192102011104
CPU ID :      RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID:        00001040
EM1 ID:        00001030
PUBLIC ID:    26A00102A58C0344C6799167A76D6F1D48E1D915
ASIC MODE ID:  00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID:        3E273BF637BE26FA
Use RAPUv11_2nd.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing RAWLOADER...
FLIC : 00400020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg  ,  Rev : 3.0  Ver : 11.34.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:03
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : 85F252E351E225CAFC4DFBC8041EABD2823E3500
ADL: Close_Session
Content: 000300000000280000000100000000
ADL: Reboot

Wait, reconneting...

rap= 26A00102A58C0344C6799167A76D6F1D48E1D915
hash= 25B977A055BE9B5DEC0C38A2A279C695
key= 8D0E28474A5AFDC50E144189B471395A9E683C10

Key file updated...

Done!

Repair SD procedure started...

Phone Imei: 353785041570408
Key file exists, no need to read...
Operating mode is OK, no need change...
Writing Super Dongle Key...  Ok!
Done!

Checking StartUp data ...
-----------------------
SDD Key status : SDData is Ok
SimLock status : SimLock is Ok

Security status : Security Damaged!!!!! :(
 - > Do Local SX4 or Server SX4 , Upload Tune ( checkbox or manual )

-----------------------

PA_SimLock Version :
PA_SL3 phone detected ,  SP_CODE_LEN : 15

Done!

Local SX4 procedure started...

Phone Imei: 353785041570408
Key file exists, no need to read...
Step 1...
Step 2...
SX4 Auth fail...
 - > Try Check "Custom Keys" checkbox and repeat
 - > If SDD original - "Use Server Sx4"

Local SX4 procedure started...

Phone Imei: 353785041570408
Use custom key...
Step 1...
Step 2...
Step 3...
SX4 Auth - Ok
Upload PM checked
Uploading RF/Battery tune to phone...
Error get phone info! Select file, please
Using : RM-469.pm
Operating mode is OK, no need change...

Field 1
  Record 0 write - Ok
  Record 2 write - Ok
  Record 4 write - Ok
  Record 6 write - Ok
  Record 7 write - Ok
  Record 8 write - Ok
  Record 13 write - Ok
  Record 16 write - Ok
  Record 18 write - Ok
  Record 20 write - Ok
  Record 22 write - Ok
  Record 23 write - Ok
  Record 24 write - Ok
  Record 26 write - Ok
  Record 28 write - Ok
  Record 29 write - Ok
  Record 31 write - Ok
  Record 33 write - Ok
  Record 34 write - Ok
  Record 35 write - Ok
  Record 39 write - Ok
  Record 40 write - Ok
  Record 41 write - Ok
  Record 42 write - Ok
  Record 43 write - Ok
  Record 44 write - Ok
  Record 45 write - Ok
Field 309
  Record 0 write - Ok
  Record 1 write - Ok
  Record 2 write - Ok
  Record 3 write - Ok
  Record 4 write - Ok
  Record 7 write - Ok
  Record 17 write - Ok

Check ST_SECURITY now...
Security status : ST_SECURITY => OK

Done!

Elapsed: 00:00:09

Upload done

Checking StartUp data ...
-----------------------
SDD Key status : SDData is Ok
SimLock status : SimLock is Ok
Security status : Security is Ok
-----------------------

PA_SimLock Version :
PA_SL3 phone detected ,  SP_CODE_LEN : 15

Done!

Phone disconected!

Connect phone on selected interface...

UO5OQ 08.12.2011 15:19
Re: Обсуждение BB5 Easy Service Tool
 
Повезло. ПО телефона не было сильно повреждено.
Далеко не всегда так получается.

Dimidrolus 08.12.2011 18:08
Re: Обсуждение BB5 Easy Service Tool
 
Ну я фартовый ж) Ещё й перед оптовиком (который шьёт уфсом) выпендрился)))) БАх, бах - готов) Да, бест клёвая штука)))

Kissoff1 05.03.2012 08:19
Re: Обсуждение BB5 Easy Service Tool
 
Вообщем так,толи после очередного обновления,толи само по себе,перестал бест работать по юсби нормально,тоесть теперь пока телефон не подключишь и не установишь драйвера,бест не хочет его распознавать,ранее такого небыло,я нажимал слить серты или прошить,подрубал тело,нажимал пауэр и поехали...
Теперь вылетает ошибка

Скрытый текст

тут скоро будут логи :)
подключения,дрова получается поставить только при подключении живого телефона :(
Что делать?

se13 05.03.2012 08:35
Re: Обсуждение BB5 Easy Service Tool
 
Цитата:
Сообщение от Kissoff1 (Сообщение 6324)
Вообщем так,толи после очередного обновления,толи само по себе,перестал бест работать по юсби нормально,тоесть теперь пока телефон не подключишь и не установишь драйвера,бест не хочет его распознавать,ранее такого небыло,я нажимал слить серты или прошить,подрубал тело,нажимал пауэр и поехали...
Теперь вылетает ошибка

Скрытый текст

тут скоро будут логи :)
подключения,дрова получается поставить только при подключении живого телефона :(
Что делать?
А раньше BEST что распознавал тело без драйверов, пока не установите драйвера не одна программа не увидит тело по USB, или у вас система не правильно работает

Kissoff1 05.03.2012 08:56
Re: Обсуждение BB5 Easy Service Tool
 
Я думал что Установив пакет дров для нокий,при подключении трупика,дрова ставятся,по крайней мере я же шил до этого времени кучу телефонов таким образом...

se13 05.03.2012 09:02
Re: Обсуждение BB5 Easy Service Tool
 
Цитата:
Сообщение от Kissoff1 (Сообщение 6327)
Я думал что Установив пакет дров для нокий,при подключении трупика,дрова ставятся,по крайней мере я же шил до этого времени кучу телефонов таким образом...
При подключения трупика надо нажать PW после этого должен увидится системой ваш трупик, если не определяется значит он труп

Kissoff1 05.03.2012 09:36
Re: Обсуждение BB5 Easy Service Tool
 
так и делается,но не пойму,Как бест раньше работал с такими трупиками,подключал,нажимал кратковременно пауэр и через 2-3 сек. бест начинал читать аппарта и всё делалось(тоесть дрова ставились)...
Теперь же дров не ищется у трупиков,а бест сразу отказывается работать,по фбас работает хотябы,но с новыми моделями приходится цеплять к мх-боксу((

se13 05.03.2012 10:19
Re: Обсуждение BB5 Easy Service Tool
 
Попробуйте на другом компьютере, пока тело не увидится компом и BEST его естественно не увидет.

UO5OQ 05.03.2012 10:29
Re: Обсуждение BB5 Easy Service Tool
 
Цитата:
Сообщение от Kissoff1 (Сообщение 6324)
Вообщем так,толи после очередного обновления,толи само по себе,перестал бест работать по юсби нормально,тоесть теперь пока телефон не подключишь и не установишь драйвера,бест не хочет его распознавать,ранее такого небыло,я нажимал слить серты или прошить,подрубал тело,нажимал пауэр и поехали...
Теперь вылетает ошибка

Скрытый текст

тут скоро будут логи :)
подключения,дрова получается поставить только при подключении живого телефона :(
Что делать?
Дело в том, что образно говоря, для Nokia устанавливается несколько драйверов.
Штуки 3-4 для Local и Normal mode и 1-2 для Flash mode, причём из них 1 драйвер для Dead mode.
Что бы считывать RPL с телефона достаточно только эти 1-2 драйверов которые для Flash mode.
А вот что бы BEST увидел телефон в Normal mode, нужны уже все драйвера.
Вывод прост: у вас НЕ все драйвера установлены.

mizuk01 21.10.2014 20:07
Re: Обсуждение BB5 Easy Service Tool
 
Вложений: 1
Это только у меня или касперский всем пакость делает в новой версии InfinityBox_install_BEST_v1.98 ?

UO5OQ 21.10.2014 22:00
Re: Обсуждение BB5 Easy Service Tool
 
Цитата:
Сообщение от mizuk01 (Сообщение 24086)
Это только у меня или касперский всем пакость делает в новой версии InfinityBox_install_BEST_v1.98 ?
Думаю всем.
Так как этот файл предназначен для Root, что Антивирусами понимается как взлом системы, что собственно таковым и является.
Добавьте его Касперскому в исключения.


Текущее время: 18:21. Часовой пояс GMT +3.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd. Перевод: zCarot
© 2007—2022 www.UO5OQ.com